1, the procurement requirements in gross thickness between 1.95-2.15cm.

2, the procurement light plate thickness 1.90-2.1cm, 85 gloss over.

3, large cutting operations Notes:

(1) blocks should be placed firmly on the platform, smooth.

(2) understand, see the big stone cut segmentation diagram.

(3) cut size under the knife before the big correction, review to be carefully and accurately.

(4) large cut stone blocks the first three films, the first stop to the first piece of stone skin destroyed, check the blocks of quality: whether the dark crack, had enjoyed, stain, color lines and other defects; check the first three films thickness is within the allowed tolerance (20mm ± 5mm), and give time to amend

(5) to make the machine check before and after operation, and maintenance of clean, clean.

(6) added: thick plates with the best cutting edge (height), especially with lines of stone species.

4, and thickness of processes Note:

(1) and thickness of the actual finished thickness of 19.5-2.0cm. Review thickness with a vernier caliper.

(2) operation carefully. Lift up sheet should pay attention to safety and to avoid damage to sheet metal.

(3) to make the machine check before and after operation, and maintenance of clean, clean.

5, Omo polishing process Note:

(1) polished up before you glue the stone plate (especially granite) gap fill them in, wait until the finished product to avoid spending a lot of plastic on human complement in beauty.

(2) abrasive polishing process carried out by a full set of polished resin.

(3) 85 gloss over.

(4) lift up boards to guard against accidental damage to sheet metal.

(5) to wear to some corners, gloss should be enough.

6, bridge cutting process Note:

(1) to cut smooth side up.

1, the procurement requirements in gross thickness between 1.95-2.15cm.

Two, the procurement light plate thickness in the 1.90-2.1cm, 85 gloss over.

3, large cutting operations Notes:

(1) blocks should be placed firmly on the platform, smooth.

(2) understand, see the big stone cut segmentation diagram.

(3) cut size under the knife before the big correction, review to be carefully and accurately.

(4) large cut stone blocks the first three films, the first stop to the first piece of stone skin destroyed, check the blocks of quality: whether the dark crack, had enjoyed, stain, color lines and other defects; check the first three films thickness is within the allowed tolerance (20mm ± 5mm), and give time to amend

(5) to make the machine check before and after operation, and maintenance of clean, clean.

(6) added: thick plates with the best cutting edge (height), especially with lines of stone species.

4, and thickness of processes Note:

(1) and thickness of the actual finished thickness of 19.5-2.0cm. Review thickness with a vernier caliper.

(2) operation carefully. Lift up sheet should pay attention to safety and to avoid damage to sheet metal.

(3) to make the machine check before and after operation, and maintenance of clean, clean.

5, Omo polishing process Note:

(1) polished up before you glue the stone plate (especially granite) gap fill them in, wait until the finished product to avoid spending a lot of plastic on human complement in beauty.

(2) abrasive polishing process carried out by a full set of polished resin.

(3) 85 gloss over.

(4) lift up boards to guard against accidental damage to sheet metal.

(5) to wear to some corners, gloss should be enough.

6, bridge cutting process Note:

(1) to cut smooth side up.

(2) saw blade to be sharp. (Under the knife before the knife sharp grinding head first)

(3) to control a good knife and cutting speed.

(4) to have allowances. (Margin for the 3-4mm, for 1 / 2 round shape when the joint shape to within 0.3mm).

(5) If there is a kind of stone lines even thicker edge to cut out together, so that large area of the lines with thicker edge lines will be worthy of years, the finished product will be beautiful and natural. (Set a number, and if there was more marked when the ridge orientation direction).

(6) to avoid missing edges, chipping, do not completely cut off, cut crooked, wrong size and so on.

(7) to make the machine before and after operation checks and maintenance, cleaning, cleaning.

7, glued setting process:

(1) color carefully, try to glue transferred to the same basic and stone colors.

(2) thickening of large flat panels to try and seal. Seal after the iron holder, fixed, and let it glue.

(3) bonding contact with the former as much as possible consistent with the sheet metal used for bonding.

(4) after the completion of glued joints does not exceed 0.3mm.

(5) in the glue, we should note that the glue would not dry shave the excess glue, to avoid spending a lot of time in the finished human beauty in shaving gel.

8, 1 / 2 round shape processes Note:

(1) because of the allowances (3-4mm), so the 1 / 2 circle more than originally scheduled when no allowances deep 3-4mm, so that after gluing the joints no more than 0.3mm.

9, hand-processing correction procedure Note:

(1) 50 degree angle in radians.

(2) amended over time to smooth the corner as far as possible the natural. Surface to be smooth.

(3) careful handling to prevent damage to countertops.

10, small surface polishing process Note:

(1) sheet metal frame or wooden frame to put away to avoid injury countertop edge, to keep the full angular.

(2) 85 gloss over.

(3) Small surface grinding to be carefully and comprehensively. Straight to straight, flat over a smooth curve to the natural, some corners in place to grind.

(4) connecting the corner office or excessive wear to the office to no touch, no wavy feeling a little edge wear to the hand and will not scratch.

11, fill plastic cosmetic procedures Note:

(1) place names should be in strict accordance with stone, the color area, neat and orderly place. Face, the need to glue the edges up in the same direction, forming a straight line. This easy and effective, rapid and accurate fill plastic beauty.

(2) color carefully, try to glue transferred to the same basic and stone colors.

(3) to master the glue dry time. Can not afford to avoid scraping the glue is too dry, no glue or glue, even the plastic scrape.

(4) when added rubber careful to avoid accidentally cross the, broken foot sheet. Prohibited sitting up on rubber sheet operations.

(5) non-chaotic place, all kinds of stone mixed.

(6) fill plastic stone varieties or color personnel by positioning the division of labor.

(7) fill plastic finished, we should clean up the site. Tools neatly.

12, handling the process of Notes (each process to be aware of, especially forklift handling)

(1) 102mm of the breakwater on the heel, non-flat.

(2) placed face to light smooth.

(3) gluing surface to use soft materials (such as foam) back pad. Avoid scratching the surface.

(4) Forklift handling process should be prudent and careful, to take the necessary protective measures to avoid obstructions or speed truck encounter uneven Ershi sheet fell, damage.

13, packaging processes Note:

(1) by exporting wooden packaging customized.

(2) placing, moving to be careful and meticulous.

(3) face to face discharge. The middle with a styrofoam / foam / plastic separated to avoid surface damage.

(4) wooden box made to be strong; boxes to needle firmly.

14, all processing is completed daily process to keep the workplace clean, tidy and health.

15, the "Taiwan panel processing operations Note" by the quality control staff circulated to each of a working procedure.

(2) saw blade to be sharp. (Under the knife before the knife sharp grinding head first)

(3) to control a good knife and cutting speed.

(4) to have allowances. (Margin for the 3-4mm, for 1 / 2 round shape when the joint shape to within 0.3mm).

(5) If there is a kind of stone lines even thicker edge to cut out together, so that large area of the lines with thicker edge lines will be worthy of years, the finished product will be beautiful and natural. (Set a number, and if there was more marked when the ridge orientation direction).

(6) to avoid missing edges, chipping, do not completely cut off, cut crooked, wrong size and so on.

(7) to make the machine before and after operation checks and maintenance, cleaning, cleaning.

7, glued setting process:

(1) color carefully, try to glue transferred to the same basic and stone colors.

(2) thickening of large flat panels to try and seal. Seal after the iron holder, fixed, and let it glue.

(3) bonding contact with the former as much as possible consistent with the sheet metal used for bonding.

(4) after the completion of glued joints does not exceed 0.3mm.

(5) in the glue, we should note that the glue would not dry shave the excess glue, to avoid spending a lot of time in the finished human beauty in shaving gel.

8, 1 / 2 round shape processes Note:

(1) because of the allowances (3-4mm), so the 1 / 2 circle more than originally scheduled when no allowances deep 3-4mm, so that after gluing the joints no more than 0.3mm.

9, hand-processing correction procedure Note:

(1) 50 degree angle in radians.

(2) amended over time to smooth the corner as far as possible the natural. Surface to be smooth.

(3) careful handling to prevent damage to countertops.

10, small surface polishing process Note:

(1) sheet metal frame or wooden frame to put away to avoid injury countertop edge, to keep the full angular.

(2) 85 gloss over.

(3) Small surface grinding to be carefully and comprehensively. Straight to straight, flat over a smooth curve to the natural, some corners in place to grind.

(4) connecting the corner office or excessive wear to the office to no touch, no wavy feeling a little edge wear to the hand and will not scratch.

11, fill plastic cosmetic procedures Note:

(1) place names should be in strict accordance with stone, the color area, neat and orderly place. Face, the need to glue the edges up in the same direction, forming a straight line. This easy and effective, rapid and accurate fill plastic beauty.

(2) color carefully, try to glue transferred to the same basic and stone colors.

(3) to master the glue dry time. Can not afford to avoid scraping the glue is too dry, no glue or glue, even the plastic scrape.

(4) when added rubber careful to avoid accidentally cross the, broken foot sheet. Prohibited sitting up on rubber sheet operations.

(5) non-chaotic place, all kinds of stone mixed.

(6) fill plastic stone varieties or color personnel by positioning the division of labor.

(7) fill plastic finished, we should clean up the site. Tools neatly.

12, handling the process of Notes (each process to be aware of, especially forklift handling)

(1) 102mm of the breakwater on the heel, non-flat.

(2) placed face to light smooth.

(3) gluing surface to use soft materials (such as foam) back pad. Avoid scratching the surface.

(4) Forklift handling process should be prudent and careful, to take the necessary protective measures to avoid obstructions or speed truck encounter uneven Ershi sheet fell, damage.

13, packaging processes Note:

(1) by exporting wooden packaging customized.

(2) placing, moving to be careful and meticulous.

1, the procurement requirements in gross thickness between 1.95-2.15cm.

Two, the procurement light plate thickness in the 1.90-2.1cm, 85 gloss over.

3, large cutting operations Notes:

(1) blocks should be placed firmly on the platform, smooth.

(2) understand, see the big stone cut segmentation diagram.

(3) cut size under the knife before the big correction, review to be carefully and accurately.

(4) large cut stone blocks the first three films, the first stop to the first piece of stone skin destroyed, check the blocks of quality: whether the dark crack, had enjoyed, stain, color lines and other defects; check the first three films thickness is within the allowed tolerance (20mm ± 5mm), and give time to amend

(5) to make the machine check before and after operation, and maintenance of clean, clean.

(6) added: thick plates with the best cutting edge (height), especially with lines of stone species.

4, and thickness of processes Note:

(1) and thickness of the actual finished thickness of 19.5-2.0cm. Review thickness with a vernier caliper.

(2) operation carefully. Lift up sheet should pay attention to safety and to avoid damage to sheet metal.

(3) to make the machine check before and after operation, and maintenance of clean, clean.

5, Omo polishing process Note:

(1) polished up before you glue the stone plate (especially granite) gap fill them in, wait until the finished product to avoid spending a lot of plastic on human complement in beauty.

(2) abrasive polishing process carried out by a full set of polished resin.

(3) 85 gloss over.

(4) lift up boards to guard against accidental damage to sheet metal.

(5) to wear to some corners, gloss should be enough.

6, bridge cutting process Note:

(1) to cut smooth side up.

(2) saw blade to be sharp. (Under the knife before the knife sharp grinding head first)

(3) to control a good knife and cutting speed.

(4) to have allowances. (Margin for the 3-4mm, for 1 / 2 round shape when the joint shape to within 0.3mm).

(5) If there is a kind of stone lines even thicker edge to cut out together, so that large area of the lines with thicker edge lines will be worthy of years, the finished product will be beautiful and natural. (Set a number, and if there was more marked when the ridge orientation direction).

(6) to avoid missing edges, chipping, do not completely cut off, cut crooked, wrong size and so on.

(7) to make the machine before and after operation checks and maintenance, cleaning, cleaning.

7, glued setting process:

(1) color carefully, try to glue transferred to the same basic and stone colors.

(2) thickening of large flat panels to try and seal. Seal after the iron holder, fixed, and let it glue.

(3) bonding contact with the former as much as possible consistent with the sheet metal used for bonding.

(4) after the completion of glued joints does not exceed 0.3mm.

(5) in the glue, we should note that the glue would not dry shave the excess glue, to avoid spending a lot of time in the finished human beauty in shaving gel.

8, 1 / 2 round shape processes Note:

(1) because of the allowances (3-4mm), so the 1 / 2 circle more than originally scheduled when no allowances deep 3-4mm, so that after gluing the joints no more than 0.3mm.

9, hand-processing correction procedure Note:

(1) 50 degree angle in radians.

(2) amended over time to smooth the corner as far as possible the natural. Surface to be smooth.

(3) careful handling to prevent damage to countertops.

10, small surface polishing process Note:

(1) sheet metal frame or wooden frame to put away to avoid injury countertop edge, to keep the full angular.

(2) 85 gloss over.

(3) Small surface grinding to be carefully and comprehensively. Straight to straight, flat over a smooth curve to the natural, some corners in place to grind.

(4) connecting the corner office or excessive wear to the office to no touch, no wavy feeling a little edge wear to the hand and will not scratch.

11, fill plastic cosmetic procedures Note:

(1) place names should be in strict accordance with stone, the color area, neat and orderly place. Face, the need to glue the edges up in the same direction, forming a straight line. This easy and effective, rapid and accurate fill plastic beauty.

(2) color carefully, try to glue transferred to the same basic and stone colors.

(3) to master the glue dry time. Can not afford to avoid scraping the glue is too dry, no glue or glue, even the plastic scrape.

(4) when added rubber careful to avoid accidentally cross the, broken foot sheet. Prohibited sitting up on rubber sheet operations.

(5) non-chaotic place, all kinds of stone mixed.

(6) fill plastic stone varieties or color personnel by positioning the division of labor.

(7) fill plastic finished, we should clean up the site. Tools neatly.

12, handling the process of Notes (each process to be aware of, especially forklift handling)

(1) 102mm of the breakwater on the heel, non-flat.

(2) placed face to light smooth.

(3) gluing surface to use soft materials (such as foam) back pad. Avoid scratching the surface.

(4) Forklift handling process should be prudent and careful, to take the necessary protective measures to avoid obstructions or speed truck encounter uneven Ershi sheet fell, damage.

13, packaging processes Note:

(1) by exporting wooden packaging customized.

(2) placing, moving to be careful and meticulous.

(3) face to face discharge. The middle with a styrofoam / foam / plastic separated to avoid surface damage.

(4) wooden box made to be strong; boxes to needle firmly.

14, all processing is completed daily process to keep the workplace clean, tidy and health.

15, the "Taiwan panel processing operations Note" by the quality control staff circulated to each of a working procedure.

(3) face to face discharge. The middle with a styrofoam / foam / plastic separated to avoid surface damage.
(4) wooden box made to be strong; boxes to needle firmly.
14, all processing is completed daily process to keep the workplace clean, tidy and health.

15, this "process processing granite kitchen countertops Note" by the quality control staff circulated to each of a working procedure.